Source-backed diagnostic reference

P1118 Code: Meaning & Diagnostic Guide

Mass Or Volume Air Flow Circuit High Input Bank 2

Reference status: This page preserves source-backed code definitions for discovery. Manufacturer/model applicability, repair steps and safety conclusions are not treated as verified unless a manufacturer-specific verified report is available.

What does P1118 mean?

  • BMW: Mass Or Volume Air Flow Circuit High Input Bank 2 Source
  • BUICK: Engine Coolant Temp Signal Out-Of Range High Source
  • CADILLAC: Engine Coolant Temp Signal Out-Of Range High Source
  • CHEVY: Engine Coolant Temp Signal Out-Of Range High Source
  • CHRYSLER: Engine Coolant Temp Signal Out-Of Range High Source
  • FORD: Manifold Absolute Temperature Circuit Low Input Source
  • GM: Engine Coolant Temp Signal Out Of Range High Source
  • GMC: Engine Coolant Temp Signal Out Of Range High Source
  • LINCOLN: Manifold Absolute Temperature Circuit Low Input Source
  • MERCURY: Manifold Absolute Temperature Circuit Low Input Source
  • OLDSMOBILE: Engine Coolant Temp Signal Out Of Range High Source
  • OTHER: Manifold Absolute Temperature Circuit Low Input Source
  • SATURN: Engine Coolant Temp Signal Out Of Range High Source
  • VOLKSWAGEN: Oxygen Sensor Heater Circuit Open Bank 1 Sensor 2 Source

P1118 quick answer

P1118 is a manufacturer-specific powertrain code, so its meaning depends on the vehicle. Check the code description for the exact make, model, year, and engine before diagnosing it.

Is P1118 generic or manufacturer-specific?

P1118 currently has manufacturer-labelled reference definitions for BMW, BUICK, CADILLAC, CHEVY, CHRYSLER, FORD and others. A universal generic definition is not asserted here. The exact vehicle make, model, year and powertrain should be confirmed before using a definition for diagnosis.

How P1118 works in the vehicle

The supplied references assign P1118 to different systems: examples include an engine coolant temperature signal, a manifold absolute temperature circuit, an air-flow circuit, and an oxygen-sensor heater circuit. These are vehicle-specific interpretations, not one universal definition. A scan tool’s vehicle-specific code information and service data are needed to identify the applicable meaning.

P1118 symptoms

Symptoms depend on what P1118 means for the particular vehicle. Possible signs may include a warning light, rough running, reduced performance, or temperature-related concerns; some vehicles may show few noticeable symptoms. These signs alone do not confirm the cause.

Possible causes of P1118

Possible causes depend on the vehicle-specific definition and may include a sensor, its wiring or connector, a circuit issue, or another related fault. P1118 alone does not establish that any particular component has failed.

How to diagnose P1118

  1. Confirm the vehicle’s make, model, year, engine, and the exact code description shown by a capable scan tool.
  2. Record other stored codes and freeze-frame data, which captures vehicle conditions when the code set.
  3. Use the manufacturer’s diagnostic procedure for that vehicle and the system named by the code description.
  4. Inspect the relevant connector and wiring for visible damage, corrosion, looseness, or poor connections.
  5. Test the circuit and related components against vehicle-specific service specifications before deciding on a repair.

How to fix P1118

Do not replace a sensor based only on P1118. The appropriate repair depends on the vehicle-specific code meaning and test results; correct any confirmed wiring, connection, circuit, or component fault, then verify the repair by rescanning.

Can I drive with P1118?

Driving advice depends on the vehicle and symptoms. Consult the owner’s manual and arrange diagnosis promptly. If the vehicle shows an overheating warning, runs abnormally, or loses power, stop when safe and follow the manual’s guidance rather than continuing to drive.

P1118 frequently asked questions

Does P1118 mean the same thing on every vehicle?

No. The supplied references show different definitions across manufacturers, so the vehicle’s exact details and code description are essential.

Does P1118 confirm a failed sensor?

No. It identifies a reported circuit or system condition, but diagnosis is needed to determine whether a sensor, wiring, connection, or another issue is responsible.

Can I clear P1118 and keep driving?

Clearing the code does not fix its cause. Follow the owner’s manual and seek diagnosis, especially if warning lights or drivability or temperature problems are present.

Search variants and canonical URL

Capitalization, underscores, hyphens, colons and spaces are normalized to this canonical code identity so alternate scan-tool formats do not create duplicate pages.