Source-backed diagnostic reference

P1413 Code: Meaning & Diagnostic Guide

Secondary Air Injection Pump Relay Control Circuit Signal Low

Reference status: This page preserves source-backed code definitions for discovery. Manufacturer/model applicability, repair steps and safety conclusions are not treated as verified unless a manufacturer-specific verified report is available.

What does P1413 mean?

  • BMW: Secondary Air Injection Pump Relay Control Circuit Signal Low Source
  • FORD: Secondary Air Injection System Monitor Circuit Low Voltage Source
  • KIA: EGR Differential Pressure Sensor Signal High Source
  • LINCOLN: Secondary Air Injection System Monitor Circuit Low Voltage Source
  • MERCURY: Secondary Air Injection System Monitor Circuit Low Voltage Source
  • OTHER: SAI System Monitor Circuit Low Input Source
  • VOLKSWAGEN: EGR Differential Pressure Sensor Signal Too High Source

P1413 quick answer

P1413 is a manufacturer-specific powertrain code. A generic reference describes it as a secondary-air-injection (SAI) system monitor circuit low input, but its meaning differs by vehicle; some references associate it with an EGR differential-pressure sensor signal that is too high. Check the definition for your exact make, model, year, and engine before diagnosing.

Is P1413 generic or manufacturer-specific?

P1413 currently has manufacturer-labelled reference definitions for BMW, FORD, KIA, LINCOLN, MERCURY, OTHER and others. A universal generic definition is not asserted here. The exact vehicle make, model, year and powertrain should be confirmed before using a definition for diagnosis.

How P1413 works in the vehicle

“Circuit low” generally means the control module detected a signal or voltage below the expected range. The generic listing points to the SAI monitor circuit, which relates to monitoring the emissions system that can send air into the exhaust. P1413 is not interpreted identically across manufacturers, so the code alone does not identify a failed part.

P1413 symptoms

The vehicle may show a check-engine light and could have no noticeable change in how it runs. Depending on the vehicle and the underlying issue, emissions-test readiness or engine performance may also be affected; these symptoms are not confirmed by the code alone.

Possible causes of P1413

Possible causes depend on the vehicle-specific definition. If it refers to the SAI monitor, a circuit, connection, or system fault could be involved. If it refers to an EGR differential-pressure sensor, that sensor circuit or related system may need checking. Neither interpretation confirms a failed component.

How to diagnose P1413

  1. Confirm the vehicle’s make, model, year, engine, and market, then look up the manufacturer-specific meaning of P1413.
  2. Scan for other diagnostic codes and record available freeze-frame data before clearing anything.
  3. Use the vehicle’s service information to identify the relevant system and prescribed checks.
  4. Have the relevant wiring, connectors, and system tested against manufacturer specifications; do not replace parts based only on the code description.
  5. If diagnosis requires specialist equipment or access near high-voltage components, use a qualified technician.

How to fix P1413

There is no single repair for P1413 across all vehicles. The appropriate repair depends on the vehicle-specific code definition and test results. Confirm the fault through service information and diagnosis before replacing or repairing any component.

Can I drive with P1413?

The code alone cannot establish whether the vehicle is safe to drive. If it runs normally and no warning indicates an urgent problem, arrange diagnosis according to the owner’s manual. Stop in a safe place and seek assistance if you notice severe running problems, overheating, smoke, or other urgent warnings.

P1413 frequently asked questions

What does P1413 mean?

A generic listing describes P1413 as an SAI system monitor circuit low input. The meaning is manufacturer-specific, and some vehicle references instead describe an EGR differential-pressure sensor signal that is too high.

Does P1413 identify a failed part?

No. It reports a detected signal or system condition, not a confirmed failed component. The exact meaning and diagnosis depend on the vehicle.

Can I drive with P1413?

The code alone does not determine driveability or safety. Consider how the vehicle behaves, follow any urgent dashboard warnings, and consult the owner’s manual or a technician.

Search variants and canonical URL

Capitalization, underscores, hyphens, colons and spaces are normalized to this canonical code identity so alternate scan-tool formats do not create duplicate pages.