P1513 Code: Meaning & Diagnostic Guide
DISA Control Circuit Signal High
What does P1513 mean?
- BMW: DISA Control Circuit Signal High Source
- FORD: Intake Manifold Runner Control Stuck Closed Source
- KIA: Idle Air Control Valve Closing Coil Low Voltage Source
- LINCOLN: Intake Manifold Runner Control Stuck Closed Source
- MERCURY: Intake Manifold Runner Control Stuck Closed Source
- OTHER: Intake Manifold Runner Control (Bank 2) Stuck Closed Source
- SUBARU: Idle Air Control Solenoid Signal 2 Circuit High Input Source
- VOLKSWAGEN: Intake Manifold Changeover Valve 2 Circuit Short To B+ Source
P1513 quick answer
P1513 is a manufacturer-specific powertrain code, so its meaning depends on the vehicle. The supplied references associate it with different intake-manifold runner, changeover-valve, DISA, or idle-air-control circuit descriptions. Check the vehicle-specific service information before diagnosing it.
Is P1513 generic or manufacturer-specific?
P1513 currently has manufacturer-labelled reference definitions for BMW, FORD, KIA, LINCOLN, MERCURY, OTHER and others. A universal generic definition is not asserted here. The exact vehicle make, model, year and powertrain should be confirmed before using a definition for diagnosis.
How P1513 works in the vehicle
A diagnostic trouble code (DTC) is a code stored by a vehicle’s control system when it detects a condition outside expected parameters. P1513 does not have one universal definition in the supplied evidence: descriptions vary by manufacturer and may refer to a valve position, a circuit signal, or a voltage condition. The code alone does not identify a failed part.
P1513 symptoms
Depending on the vehicle and the applicable definition, a driver might notice changes in idle, engine response, or performance, or see a warning light. These symptoms are not established for every vehicle with P1513, and some vehicles may show few obvious symptoms.
Possible causes of P1513
Possible explanations depend on the vehicle-specific code definition and may include a sticking intake control mechanism, an electrical connection or wiring issue, or a control-system problem. These are possibilities, not confirmed causes; P1513 alone does not prove that any particular component has failed.
How to diagnose P1513
- Confirm the vehicle’s make, model, year, engine, and market, then look up P1513 in reliable service information for that exact vehicle.
- Scan for other stored codes and record freeze-frame data, which captures operating conditions when a code was set.
- Use the vehicle-specific diagnostic procedure to check the relevant circuit or intake-control system; inspect accessible connectors and wiring for visible damage or loose connections.
- Compare test results with the specified values before deciding whether a component or wiring needs repair.
- Clear the code only after documenting it and completing appropriate checks, then verify whether it returns under suitable conditions.
How to fix P1513
There is no single repair for P1513 across all vehicles. Follow the exact vehicle’s diagnostic procedure and repair only the issue supported by test results. Avoid replacing a valve or actuator based on the code description alone; seek a qualified technician if diagnosis requires specialized tools or procedures.
Can I drive with P1513?
The code by itself does not establish whether continued driving is safe. Consider the vehicle’s behavior and warning lights, consult the owner’s manual, and arrange diagnosis. If the engine runs poorly, loses power, or behaves unpredictably, stop in a safe place and seek professional advice.
P1513 frequently asked questions
What does P1513 mean?
Its meaning varies by manufacturer and vehicle. Supplied references associate it with several different intake-control and idle-air-control descriptions, so verify the definition for your exact vehicle.
Does P1513 mean a specific part has failed?
No. The code identifies a detected condition, not necessarily a failed component. Vehicle-specific testing is needed to find the cause.
Can I keep driving with P1513?
The code alone cannot determine that. Use the vehicle’s symptoms and owner’s manual as context, and seek diagnosis—especially if performance or engine behavior changes.
How is P1513 diagnosed?
Confirm the vehicle-specific definition, review related codes and freeze-frame data, then test the relevant circuit or intake-control system using the manufacturer’s procedure.
Search variants and canonical URL
Capitalization, underscores, hyphens, colons and spaces are normalized to this canonical code identity so alternate scan-tool formats do not create duplicate pages.