U140600 Code: Meaning & Diagnostic Guide
Audi TSB 2077115/1 defines U140600 as “Static current too high” and instructs technicians to run the relevant test program when it is logged at diagnostic address 0019. The bulletin applies to Q4 model years 2022–2024 and discusses the Q4’s high-voltage battery and electric-drive operation.
What does U140600 mean?
- Audi: Audi TSB 2077115/1 defines U140600 as “Static current too high” and instructs technicians to run the relevant test program when it is logged at diagnostic address 0019. The bulletin applies to Q4 model years 2022–2024 and discusses the Q4’s high-voltage battery and electric-drive operation. Source
- Volkswagen: “Quiescent current too large” (also rendered “Static current too high”). Source
U140600 quick answer
U140600 is described as “quiescent current too large” or “static current too high.” In plain language, it indicates that more electrical current than expected may be drawn while the vehicle is at rest. The exact meaning and diagnostic procedure can depend on the vehicle.
Is U140600 generic or manufacturer-specific?
U140600 currently has manufacturer-labelled reference definitions for Audi, Volkswagen. A universal generic definition is not asserted here. The exact vehicle make, model, year and powertrain should be confirmed before using a definition for diagnosis.
How U140600 works in the vehicle
Quiescent current is the small amount of power a vehicle uses while parked. U140600 reports that this resting current is considered too high; the code alone does not identify the cause or a failed component. Audi TSB 2077115/1 describes a specific procedure for certain 2022–2024 Q4 vehicles when the code is logged at diagnostic address 0019. That procedure should not be assumed to apply to other vehicles.
U140600 symptoms
A vehicle with excessive resting current might have a discharged or weakened 12-volt battery, especially after being parked. The code may also be stored without an obvious symptom. These possibilities do not confirm the vehicle’s condition.
Possible causes of U140600
Possible explanations can include an electrical load that remains active after parking, a control module that does not enter its low-power state, or a battery or charging-system issue. U140600 alone does not establish any of these as the cause.
How to diagnose U140600
- Confirm the code with a scan tool and record which control module or diagnostic address reported it.
- Check the vehicle-specific service information for the code and any applicable diagnostic procedure.
- Have a qualified technician assess the 12-volt battery and measure resting current using the vehicle maker’s procedure.
- If the vehicle is an applicable 2022–2024 Audi Q4 and the code is logged at address 0019, consult Audi TSB 2077115/1 for its specified test program.
- Review test results before replacing parts; the code by itself does not identify a failed component.
How to fix U140600
The appropriate repair depends on test results and vehicle-specific service information. Ask a qualified technician to identify the source of the excess resting current before authorizing repairs. Do not assume that a battery or any particular component needs replacement based on this code alone.
Can I drive with U140600?
The code alone does not determine whether a vehicle is safe to drive. If the vehicle starts and operates normally, consult its manual or a qualified technician about next steps. If it will not start, displays other warnings, or loses electrical power, arrange assistance rather than relying on it for travel.
U140600 frequently asked questions
What does U140600 mean?
It is described as “quiescent current too large” or “static current too high,” meaning resting electrical current may be above the expected level.
Does U140600 identify a bad battery?
No. A battery problem is one possibility, but the code alone does not identify a failed battery or any other component.
Can U140600 drain the battery?
If excessive current is actually being drawn while the vehicle is parked, it could contribute to battery discharge. Diagnosis is needed to determine whether that is happening.
Does the Audi Q4 test procedure apply to every vehicle with U140600?
No. The cited Audi bulletin describes a procedure for specified 2022–2024 Q4 vehicles when the code is logged at diagnostic address 0019. Check the service information for the specific vehicle.
Search variants and canonical URL
Capitalization, underscores, hyphens, colons and spaces are normalized to this canonical code identity so alternate scan-tool formats do not create duplicate pages.