EV Diagnostics
Verified EV diagnostic knowledge page

Genesis P076300

19-AT-008G Page 12 of 12 31. Input the 8-digit code recorded in Step 10 in the blank spaces in the GDS. Select OK. Input the 8 digit code again and select OK. The GDS will c

DriveNot yet established by verified evidence.
ChargeNot yet established by verified evidence.
ServiceContact a Genesis dealer or qualified Genesis service facility for diagnosis, particularly if solenoid-valve replacement has been performed or is being considered.
Confidence95%

Quick answer

For a 2023–2024 Genesis G80 (US), verified NHTSA manufacturer communication 19-AT-008G identifies P076300 as one of the solenoid codes for which an Automatic Transaxle “Oil Pressure Characteristics Input” procedure may be required after solenoid-valve replacement. The supplied evidence does not establish a plain-language fault definition for P076300.

This page separates verified manufacturer/regulator evidence from supporting material. Unsupported causes, repairs or safety conclusions are not guessed.

Video guides

Watch Videos

Relevant videos play here without leaving this diagnostic page.

No sufficiently relevant embeddable video has been accepted for this diagnostic yet.

Videos are supporting material and never override OEM or regulator evidence.

1. What does P076300 mean?

For a 2023–2024 Genesis G80 (US), verified NHTSA manufacturer communication 19-AT-008G identifies P076300 as one of the solenoid codes for which an Automatic Transaxle “Oil Pressure Characteristics Input” procedure may be required after solenoid-valve replacement. The supplied evidence does not establish a plain-language fault definition for P076300.

2. Technical explanation

The verified source directs use of GDS service software: select S/W Management, Automatic Transaxle, then Oil Pressure Characteristics Input (Solenoid Valve Replacement), select the relevant solenoid type, and follow prompts. The source says this procedure is necessary only for P075300, P075800, P076300, P076800, and P077300. It also refers to entering an 8-digit code previously recorded during the procedure. The supplied evidence does not establish what component failure, electrical condition, hydraulic condition, or vehicle behavior set P076300.

3. What system is affected?

Automatic transaxle / solenoid oil-pressure characteristics input procedure, as identified by TSB 19-AT-008G.

4. How serious is this code?

Not yet established by verified evidence.

5. Symptoms you may notice

  • Not yet established by verified evidence.

6. Possible causes

  • Not yet established by verified evidence.

7. Can I still drive the vehicle?

Not yet established by verified evidence.

8. Can I charge the vehicle?

Not yet established by verified evidence.

9. What you can safely do

  • Arrange diagnosis by a Genesis-qualified service facility.
  • Do not attempt transmission solenoid replacement or GDS programming without appropriate service training and equipment.
  • Record the stored diagnostic code and any accompanying codes for the service visit.

10. Step-by-step troubleshooting

  1. Use a suitable scan tool to confirm whether P076300 is stored and document accompanying diagnostic information.
  2. For an applicable repair involving solenoid-valve replacement, follow Genesis TSB 19-AT-008G through GDS: S/W Management > Automatic Transaxle > Oil Pressure Characteristics Input (Solenoid Valve Replacement).
  3. The supplied evidence does not provide further diagnostic test steps, wiring checks, fluid checks, or component replacement criteria.

11. When to contact service

Contact a Genesis dealer or qualified Genesis service facility for diagnosis, particularly if solenoid-valve replacement has been performed or is being considered.

12. What the service center may check

  • Confirm vehicle applicability: Genesis G80, model years 2023–2024, US market.
  • Confirm whether P076300 is present.
  • If a relevant solenoid valve has been replaced, perform the GDS Oil Pressure Characteristics Input procedure specified by TSB 19-AT-008G.
  • Enter the 8-digit code recorded during the procedure twice when prompted by GDS, as described in the supplied source.

13. Possible repair or resolution

  • The verified communication describes a required GDS oil-pressure-characteristics input procedure for P076300 when applicable after solenoid-valve replacement.
  • Whether replacement, adjustment, programming beyond this procedure, or another repair resolves P076300 is not yet established by verified evidence.

14. Affected vehicles

15. Related TSBs / service bulletins

  • Genesis TSB 19-AT-008G, published through NHTSA as Manufacturer Communication PDF 10253024 on 2019-04-08. It lists P076300 among codes requiring the Automatic Transaxle Oil Pressure Characteristics Input (Solenoid Valve Replacement) procedure.

16. Recall information

  • Not yet established by verified evidence.

17. Official manufacturer information

NHTSA Manufacturer Communication PDF 10253024, Genesis TSB 19-AT-008G: https://static.nhtsa.gov/odi/tsbs/2019/MC-10253024-0001.pdf

19. Frequently asked questions

What does P076300 mean on a Genesis G80?

The supplied verified evidence does not establish a plain-language definition. It identifies P076300 as a solenoid-related code covered by the Genesis automatic-transaxle oil-pressure-characteristics input procedure.

Does P076300 require a special procedure after solenoid replacement?

Yes. TSB 19-AT-008G states that the Oil Pressure Characteristics Input (Solenoid Valve Replacement) procedure is necessary for P076300, among a limited list of codes.

Can I drive or charge with P076300?

Not yet established by verified evidence.

20. Sources & verification

Verified
Genesis P076300: 19-AT-008G Page 12 of 12 31. Input the 8-digit code… | EV Diagnostics