Genesis P075800
19-AT-008G Page 12 of 12 31. Input the 8-digit code recorded in Step 10 in the blank spaces in the GDS. Select OK. Input the 8 digit code again and select OK. The G
Quick answer
For a 2023–2024 Genesis G80 in the US, verified evidence links DTC P075800 to an Automatic Transaxle service procedure: “Oil Pressure Characteristics Input (Solenoid valve Replacement).” The supplied evidence does not establish the code’s plain-language fault definition, drivability, charging status, symptoms, or a specific failed part.
This page separates verified manufacturer/regulator evidence from supporting material. Unsupported causes, repairs or safety conclusions are not guessed.
Watch Videos
Relevant videos play here without leaving this diagnostic page.
No sufficiently relevant embeddable video has been accepted for this diagnostic yet.
Videos are supporting material and never override OEM or regulator evidence.
1. What does P075800 mean?
For a 2023–2024 Genesis G80 in the US, verified evidence links DTC P075800 to an Automatic Transaxle service procedure: “Oil Pressure Characteristics Input (Solenoid valve Replacement).” The supplied evidence does not establish the code’s plain-language fault definition, drivability, charging status, symptoms, or a specific failed part.
2. Technical explanation
The verified NHTSA-hosted Genesis manufacturer communication 19-AT-008G identifies P075800 among solenoid-related transmission DTCs. It states that, after replacement of certain solenoids, GDS software management must be used to perform Automatic Transaxle “Oil Pressure Characteristics Input (Solenoid valve Replacement).” The procedure includes selecting the solenoid type and entering an 8-digit code recorded earlier in the procedure twice. This required characteristics-input procedure specifically includes P075800.
3. What system is affected?
Automatic Transaxle / transmission solenoid service procedure.
4. How serious is this code?
Not yet established by verified evidence.
5. Symptoms you may notice
Not yet established by verified evidence.
6. Possible causes
- Not yet established by verified evidence. The supplied bulletin associates P075800 with a solenoid-related Automatic Transaxle service procedure, but it does not establish a specific cause or failed component.
7. Can I still drive the vehicle?
Not yet established by verified evidence.
8. Can I charge the vehicle?
Not yet established by verified evidence.
9. What you can safely do
- Arrange diagnosis by a Genesis-qualified service facility or other appropriately equipped technician.
- Provide the technician with DTC P075800 and reference Genesis bulletin 19-AT-008G.
- Do not attempt transmission-solenoid replacement or GDS calibration/programming without proper service equipment and training.
10. Step-by-step troubleshooting
- Confirm the stored DTC with compatible diagnostic equipment.
- For applicable vehicles, review Genesis bulletin 19-AT-008G and follow the manufacturer procedure as applicable.
- If a listed solenoid has been replaced, the bulletin specifies using GDS S/W Management: Automatic Transaxle → Oil Pressure Characteristics Input (Solenoid valve Replacement).
- The verified procedure requires selection of the solenoid type and entry of the recorded 8-digit code twice.
11. When to contact service
Service evaluation is appropriate because the verified evidence identifies a manufacturer Automatic Transaxle solenoid service/calibration procedure for P075800. Urgency and whether the vehicle may be driven are not established by the supplied evidence.
12. What the service center may check
- Retrieve and document DTC P075800.
- Determine whether a relevant transmission solenoid has been replaced.
- Where applicable, perform the manufacturer-specified Oil Pressure Characteristics Input procedure using GDS.
- Select the applicable solenoid type in GDS.
- Enter the 8-digit code recorded during the bulletin procedure twice, as directed by the bulletin.
13. Possible repair or resolution
- If applicable after solenoid replacement, complete the GDS Automatic Transaxle Oil Pressure Characteristics Input procedure described in Genesis bulletin 19-AT-008G.
- No specific mechanical repair or component replacement is established by the supplied verified evidence.
14. Affected vehicles
- Genesis G80 · 2023–2024 · US
15. Related TSBs / service bulletins
- Genesis TSB 19-AT-008G, NHTSA Manufacturer Communication PDF 10253024, published April 8, 2019. It lists P075800 among solenoid DTCs requiring the Oil Pressure Characteristics Input procedure following replacement of the relevant solenoid.
16. Recall information
No recall relationship is established by verified evidence.
17. Official manufacturer information
Verified source: NHTSA-hosted Genesis manufacturer communication 19-AT-008G (MC-10253024-0001): https://static.nhtsa.gov/odi/tsbs/2019/MC-10253024-0001.pdf. Supplied applicability: 2023–2024 Genesis G80, US.
19. Frequently asked questions
What does P075800 mean on an applicable Genesis G80?
The supplied verified evidence does not provide a plain-language definition. It identifies P075800 as one of the solenoid-related Automatic Transaxle DTCs covered by Genesis bulletin 19-AT-008G.
Does P075800 require a programming or calibration procedure?
The bulletin states that Oil Pressure Characteristics Input is necessary for specified solenoids after solenoid replacement, and P075800 is included in its listed DTCs. The procedure uses GDS and requires the recorded 8-digit code to be entered twice.
Can I drive with P075800?
Not yet established by verified evidence.
Is P075800 related to EV battery charging?
The supplied evidence concerns the Automatic Transaxle. Charging impact is not yet established by verified evidence.