PHEV model family

Audi Q5 error codes and diagnostics

Diagnostic coverage for model years 2021–2025. Verified entries below are linked to this model family by source-backed applicability evidence; model membership alone is never used to invent a code relationship.

PowertrainPHEV
Model years2021–2025
Verified diagnostics68
Evidence statusVerified

Verified Verified Audi Q5 diagnostic codes

Showing 36–68 of 68 verified records for this model. Each result opens a manufacturer-specific report with the code meaning, affected vehicles, source evidence and the full diagnostic knowledge page where available.

P0A1B00P0A1B00 is an Audi DTC meaning “Drive motor ‘A’ Control Module.” Verified Audi bulletins associate it with Electric Drive 2 (J944, address 00CE) on certain vehicles and describe several distinct bulletin-specific scenarios; a code alone does not establish one cause. · 2020View diagnostic report →P0A2F00P0A2F00 means “Drive Motor ‘A’ Over Temperature.” Verified evidence applies this information to the 2020 Audi Q5 in the US. · 2020View diagnostic report →P0A7D00P0A7D00 is documented by Audi as “Hybrid/EV Battery Pack State Of Charge Low” for vehicles with a 48 V electrical system. The referenced Audi communication states that the 48 V battery may enter a low-voltage protection state and will not accept a charge. · 2017–2024View diagnostic report →P0A9500Verified diagnostic record · 2020–2022View diagnostic report →P0AA200Verified diagnostic record · 2020–2022View diagnostic report →P0AA500Audi DTC P0AA500 is identified in verified Audi service information as “Hybrid/EV Battery Negative Contactor Circuit Stuck Open.” For the specified condition, Audi states not to proceed according to GFF, which may suggest replacement of the high-voltage battery switching unit/Battery Junction Box (SX6). · 2020–2022View diagnostic report →P0AC000Verified diagnostic record · 2020View diagnostic report →P0C4300For a verified applicable vehicle, this Audi service information links DTC P0C4300 to a condition addressed by updated software for the thermal management control module (J1024, address word 00C5). · 2020View diagnostic report →P0CE100For a 2020 Audi Q5 in the US, DTC P0CE100 is documented in Audi service communications as a code that may be stored in the thermal management control module. Audi’s documented production solution is updated software for thermal management control module J1024 (address word 00C5). · 2020View diagnostic report →P0E5E00Verified diagnostic record · 2022–2025View diagnostic report →P169A00Audi DTC P169A00 means “Transport mode active.” Verified Audi service communications state that the communication unit (ConBox) can remain in transport/flight mode when it is not taken out of transport mode with a VAS 6154 diagnostic interface. · 2019–2023View diagnostic report →P251500P251500 is an Audi thermal-management DTC for an electrical fault in refrigerant pressure sensor 2. Audi documentation links it to loss of pressure evaluation and reports that cabin air conditioning may not cool, sometimes intermittently. · 2020–2022View diagnostic report →P33F000Verified diagnostic record · 2020View diagnostic report →SOS Emergency Call function: malfunction. Function unavailable. Please contact serviceFor certain 2023 US Audi Q5, e-tron, e-tron GT, and RS e-tron GT vehicles, this alert indicates that the SOS Emergency Call function is malfunctioning or unavailable. Audi’s referenced technical service bulletin documents the instrument-cluster message and directs the customer to contact service. · 2023View diagnostic report →SOS – Emergency call malfunction, please contact serviceFor certain 2021 US Audi models, this instrument-cluster message is covered by Audi manufacturer communications concerning the emergency-call module and communication unit. Contact Audi service for diagnosis. · 2021View diagnostic report →Start/stop system: system fault. Function unavailable. Please contact workshopThis Audi instrument-cluster alert indicates that the start/stop system is unavailable because the vehicle has detected a system fault. The supplied official Audi manufacturer communication instructs contact with a workshop. · 2016–2025View diagnostic report →Traffic Jam Assist: malfunction!Audi’s “Traffic Jam Assist: malfunction!” alert is a verified instrument-cluster malfunction indication. An Audi technical service bulletin (TSB) documents it together with possible stored faults involving the front camera R242 and distance regulation control module J428. · 2019–2022View diagnostic report →U002800For a 2020 Audi Q5 in the US, DTC U002800 means “Vehicle Communication Bus A.” An official Audi/NHTSA service communication lists it among possible stored faults when warning lamps are illuminated and/or the vehicle cannot be driven. · 2020View diagnostic report →U002900For a 2020 Audi Q5 in the US, DTC U002900 means “Vehicle Communication Bus A Performance.” An Audi/NHTSA manufacturer communication lists this code among possible stored faults in a condition involving power-electronics-related faults. The source does not establish whether the vehicle is safe to drive or charge. · 2020View diagnostic report →U003600For a 2020 Audi Q5 in the US, DTC U003600 is documented in an Audi/NHTSA manufacturer communication as “Vehicle Communication Bus A (-) shorted to Bus A (+).” It may occur with multiple warning lamps and, in some cases, a vehicle that cannot be driven. · 2020View diagnostic report →U011000U011000 means “Lost Communication With Drive Motor Control Module.” Verified Audi evidence links this DTC to specific conditions in certain U.S. Audi vehicles, including a documented software issue and, in a separate bulletin, possible chafing of a 12V power-electronics wiring harness against underbody trim. · 2020View diagnostic report →U059B00Verified diagnostic record · 2020View diagnostic report →U101400For the listed Audi vehicles, U101400 may be stored in telematics control module J949 (address word 0075) because of a start-up timing issue. Audi’s communication states that no repair is available and repairs should not be performed for this concern. · 2019–2020View diagnostic report →U110300For specified 2021–2022 US Audi models, DTC U110300 is identified in Audi service communications as “Production mode active” in the telematics control module J949 (address word 0075). Audi directs technicians to run the control-module replacement test plan through ODIS Guided Functions, without replacing the module. · 2021–2022View diagnostic report →U112100Audi DTC U112100 means “data bus, missing message.” Verified evidence links it to more than one system context, including adaptive air suspension and the high-voltage battery charger control module. The code alone does not establish a single failed part or whether the vehicle is safe to drive or charge. · 2020–2022View diagnostic report →U112300Verified diagnostic record · 2019–2023View diagnostic report →U121C00For a 2020 Audi Q5 in the US, DTC U121C00 means “Drive Motor ‘A’ No Communication.” Audi’s official service communication identifies possible chafing of the 12V wiring harness for the power electronics (J841, address word 0051) against underbody trim as the technical background for a bulletin that includes this DTC. · 2020View diagnostic report →U13EB00U13EB00 is an Audi DTC meaning “Emergency call module and communication unit Flight mode activated.” Verified Audi bulletins associate it with the emergency-call/communications module at address 0075. · 2019–2022View diagnostic report →U140500Audi DTC U140500 means “Terminal 15 Implausible signal.” Verified evidence links it to specific Audi service bulletins, but driving, charging, and overall severity are not yet established by verified evidence. · 2020View diagnostic report →U142100Audi DTC U142100 means the gateway cannot communicate with the emergency call module and communication unit (ConBox). Verified Audi bulletins associate it with an SOS malfunction message on certain vehicles and identify specific startup or transport-mode situations in documented cases. · 2019–2023View diagnostic report →U14A00Audi DTC U14A00 is identified as “Terminal 30.” Verified NHTSA-hosted Audi manufacturer communications state that this code may be stored in the ECM. Its driving, charging, and service urgency are not yet established by verified evidence supplied. · 2017–2025View diagnostic report →U153E00U153E00 indicates that the emergency-call module/communication unit could not be recognized on the mobile communications network. Audi documentation associates it with an SOS emergency-call-function-deactivated message and a loss of connection to the mobile network operator (AT&T). · 2019–2020View diagnostic report →Vehicle start system: fault. Please contact workshopVerified diagnostic record · 2016–2024View diagnostic report →

About this model coverage

EV Diagnostics separates vehicle catalog data from diagnostic applicability. A code is listed as verified for Audi Q5 only when supporting evidence connects that diagnostic identity to the model or its documented model-year range.

Related navigation

All Audi EV models and diagnostics · Search all diagnostic codes · How verification works