PHEV model family
Audi Q5 error codes and diagnostics
Diagnostic coverage for model years 2021–2025. Verified entries below are linked to this model family by source-backed applicability evidence; model membership alone is never used to invent a code relationship.
PowertrainPHEV
Model years2021–2025
Verified diagnostics68
Evidence statusVerified
Verified Verified Audi Q5 diagnostic codes
Showing 1–35 of 68 verified records for this model. Each result opens a manufacturer-specific report with the code meaning, affected vehicles, source evidence and the full diagnostic knowledge page where available.
Air suspension: system faultAudi OEM alert: “Air suspension: system fault.” Verified Audi technical-service communications link this instrument-cluster message to faults recorded in the suspension control unit J775 (diagnostic address 0074) on specified US-market vehicles. · 2019–2023View diagnostic report →Antenna MalfunctionFor certain 2023 Audi US models, an “Antenna Malfunction” message can be displayed on the MMI screen. Audi manufacturer communications link this message to a possible communication issue involving the emergency call module and communication unit. · 2023View diagnostic report →Audi Active Lane Assist: malfunction!Verified diagnostic record · 2021–2023View diagnostic report →B113E29B113E29 is documented by Audi service communications as “Closing assistance Range/Performance” in the rear lid control module J605 (address 006D). It is associated with a power rear lid that may not close completely or latch in the secondary position. · 2020–2021View diagnostic report →B126101Verified diagnostic record · 2019–2024View diagnostic report →B126111B126111 indicates a short circuit to ground reported for the windshield washer pump. Audi’s verified bulletin states that a blocked washer pump caused by frozen washer fluid can increase pump resistance and store this DTC; it may be static or sporadic. · 2019–2024View diagnostic report →B126113Audi DTC B126113 means “Windshield washer pump Open circuit.” Verified evidence links it to an inoperative washer system and/or windshield-washer solvent leak, with the DTC stored in the BCM/J519 control module. · 2019–2024View diagnostic report →B126CF0B126CF0 indicates that the Audi navigation database is malfunctioning. Verified Audi service information links it to a navigation map over-the-air update that was interrupted by an internal reset, leaving the database corrupted. · 2021View diagnostic report →B126CF1Audi DTC B126CF1 means “Navigation database not available.” Verified Audi/NHTSA communications associate it with a navigation system that remains initializing or has a corrupt or incomplete map after an over-the-air update. The cited bulletin applies only in combination with recall 91DZ. · 2021View diagnostic report →B129B11Verified diagnostic record · 2021View diagnostic report →B129C11Verified diagnostic record · 2021View diagnostic report →B12CB15For a 2020 Audi Q5 in the US, DTC B12CB15 is documented as a left back-up light bulb circuit fault: “Open circuit/short circuit to B+.” Audi’s bulletin describes a possible reverse-lamp internal circuit-board separation in the rear-bumper lamp. · 2020View diagnostic report →B12CC15For a 2020 Audi Q5 PHEV in the US, DTC B12CC15 is identified in an Audi/NHTSA manufacturer communication as: right back-up light bulb open circuit/short circuit to B+. The bulletin associates it with a tail-lamp warning in the instrument cluster. · 2020View diagnostic report →B13BCF2Verified diagnostic record · 2016–2023View diagnostic report →B145504Verified diagnostic record · 2016–2022View diagnostic report →B14BF01For covered Audi vehicles, DTC B14BF01 is documented in Audi service communications as a steering-column vertical-adjustment motor electrical error, with symptom code 66145. The documented correction is a software update followed by clearing the control unit. · 2019–2021View diagnostic report →B200000Audi DTC B200000 means “Ctrl. Module Faulty.” For the verified 2021 US Audi A7, A8, Q5, and e-tron applications, Audi documentation identifies it in telematics control module J949 (address 0075) with symptom code 131096. Audi states it can be stored erroneously when transport mode is removed. · 2021View diagnostic report →B200049Verified diagnostic record · 2019–2022View diagnostic report →B200096Verified diagnostic record · 2021–2022View diagnostic report →B200FF0Audi DTC B200FF0 means “Internal malfunction.” Verified Audi bulletins show it can be stored either in the suspension control unit J775 or in the instrument cluster J285, depending on the applicable bulletin and vehicle condition. · 2019–2023View diagnostic report →B200FF1For certain 2019–2023 US Audi A7, A8, Q5, and e-tron vehicles, DTC B200FF1 is documented by Audi as an “Internal malfunction” in the suspension control unit J775 (address 0074). · 2019–2023View diagnostic report →B200FF3Audi DTC B200FF3 is documented as an internal malfunction in several control-module contexts. For the Audi e-tron suspension-control-module case, Audi states that it can result from a timing issue in module memory access; follow the applicable Audi test plan if additional suspension DTCs are present. · 2019–2023View diagnostic report →B200FF4Audi DTC B200FF4 is documented as “Internal malfunction” in the suspension control unit J775 (address 0074). · 2019–2023View diagnostic report →B200FF5Audi DTC B200FF5 is identified in verified Audi service communications as an internal malfunction stored in suspension control module J775 (address 0074). For certain vehicles, Audi attributes B200FF5 to a timing issue in the module’s memory access. · 2019–2023View diagnostic report →B239C11Verified diagnostic record · 2021View diagnostic report →C10AC07Verified diagnostic record · 2019–2022View diagnostic report →C1260F0Audi DTC C1260F0 means: “compressor control unit for adaptive suspension, no communication.” Verified Audi service information associates it with an air-suspension malfunction warning and directs inspection of relevant wiring and connector contacts. · 2019–2021View diagnostic report →Drive system: fault. Please contact workshopVerified diagnostic record · 2025View diagnostic report →Electrical system: fault. Please contact workshopVerified diagnostic record · 2020–2022View diagnostic report →Electrical system: fault. Safely stop vehicleVerified diagnostic record · 2020–2022View diagnostic report →Emergency call function: malfunction! Function unavailable. Please contact serviceThis Audi alert indicates that the emergency call function is unavailable and asks the driver to contact service. Verified manufacturer communications document the same instrument-cluster warning and refer to diagnostic trouble codes stored in the Emergency Call Module and Communication Unit. · 2021–2024View diagnostic report →Fault: Limited warning messages...Verified diagnostic record · 2019–2023View diagnostic report →Fault: Limited warning messgesVerified diagnostic record · 2019–2025View diagnostic report →Instrument cluster: fault. Limited warning messages. Please contact workshopVerified diagnostic record · 2019–2025View diagnostic report →P053000For certain 2020–2022 U.S. Audi models, DTC P053000 indicates an air-conditioning system pressure-sensor electrical fault. Audi’s bulletin links it to loss of cabin cooling, which may be intermittent. · 2020–2022View diagnostic report →
About this model coverage
EV Diagnostics separates vehicle catalog data from diagnostic applicability. A code is listed as verified for Audi Q5 only when supporting evidence connects that diagnostic identity to the model or its documented model-year range.
Related navigation
All Audi EV models and diagnostics · Search all diagnostic codes · How verification works