EV manufacturer

Audi EV diagnostics

Explore Audi diagnostic codes for A7, A8 and other verified model families. Review source-backed evidence and supported model applicability.

11 model families with verified coverage266 verified
Audi Q4 e-tron — representative Audi EV/PHEV for diagnostic code coverageAudi Q4 e-tron

Models with verified diagnostic coverage

Verified Manufacturer-level verified records

These records passed the verified evidence gate. Model applicability is shown only where separately supported.

Drive system: fault. Please contact workshopVerified diagnostic recordP0E5E00Verified diagnostic recordP0DBC00Audi Circular 93RA lists P0DBC00 as “Hybrid/EV Battery Cell Balancing Circuit E” in high-voltage battery cell-module diagnostic and repair guidance.P0DCC00Audi Circular 93RA lists P0DCC00 as “Hybrid/EV Battery Cell Balancing Circuit I” in high-voltage battery cell-module diagnostic and repair guidance.P0DAC00Audi Circular 93RA lists P0DAC00 as “Hybrid/EV Battery Cell Balancing Circuit A” in high-voltage battery cell-module diagnostic and repair guidance.B153813For certain 2020–2021 US Audi A7, A8, and e-tron vehicles, DTC B153813 means “steering wheel heater Open circuit.” Audi’s cited manufacturer communication says not to perform repairs for this concern; repairs may be denied.B145504Verified diagnostic recordB200FF5Audi DTC B200FF5 is identified in verified Audi service communications as an internal malfunction stored in suspension control module J775 (address 0074). For certain vehicles, Audi attributes B200FF5 to a timing issue in the module’s memory access.B200FF3Audi DTC B200FF3 is documented as an internal malfunction in several control-module contexts. For the Audi e-tron suspension-control-module case, Audi states that it can result from a timing issue in module memory access; follow the applicable Audi test plan if additional suspension DTCs are present.C102029Verified diagnostic recordU015100Verified diagnostic recordC051F00Verified diagnostic recordC102229Audi DTC C102229 means “Lateral acceleration 1 implausible signal.” For applicable 2019–2020 US Audi e-tron vehicles, Audi documented that it may be stored in the ABS control module with multiple cluster warnings, including an ESC warning, during a vehicle sleep-mode/wake-up timing condition.C052000Verified diagnostic recordC12B3FAFor certain 2019–2020 US Audi A8 and e-tron vehicles, DTC C12B3FA is documented as a front camera for driver-assistance systems communication fault with symptom code 221189. Audi technical-service communications describe it as a rare software-related scenario that can cause driver-assistance warnings.C12B3F0C12B3F0 is documented by Audi as “front camera for driver assist systems, dynamic calibration limit exceeded” with symptom code 221202. It is associated with the front camera for assistance systems R242 and can appear with adaptive-light or Audi pre sense warnings.C12D5FAC12D5FA is an Audi driver-assistance-system DTC: “control unit for driver assist systems, picture processor does not respond,” with symptom code 221281. Audi documents it as an intermittent condition linked to an overly sensitive diagnostic function in applicable bulletins.C12EBF3C12EBF3 is an Audi distance-control laser DTC meaning “laser for distance control, range recognition restricted.” It is documented for certain US 2019–2020 Audi A8 and e-tron vehicles.B200FF9Audi DTC B200FF9 means “internal problem.” Verified Audi/NHTSA communications link it to driver-assistance control modules and, in documented cases, overly sensitive software diagnostics. Applicability is verified for specified 2019–2022 US Audi models, including the e-tron, e-tron GT, and RS e-tron GT.U029200For certain 2019 Audi e-tron vehicles in the US, DTC U029200 may be associated with an incorrectly routed low-voltage wiring harness for the rear electric drive motor. Audi states this harness may be damaged, and fuses SJ7 and/or SD5 may be open.B200087For the verified Audi applications, B200087 is a static software-compatibility DTC stored in Information Electronics Control Module 1 (J794, address 005F). Audi’s bulletin states it results from an unintentional data lookup that returns no result, cannot be deleted, and does not restrict functionality.B122D29For certain 2019–2020 US Audi e-tron vehicles, DTC B122D29 identifies an implausible signal from the central-locking locking unit. Audi manufacturer communications state that the software needs to be updated in the door electronics control module(s).C12B3F2For applicable 2019–2020 US Audi A8 and e-tron vehicles, DTC C12B3F2 indicates: “front camera for driver assist systems, wrong vehicle identification number, static.” Audi’s documented technical background is that the software needs recalibration.B1298FCVerified diagnostic recordU153E00U153E00 indicates that the emergency-call module/communication unit could not be recognized on the mobile communications network. Audi documentation associates it with an SOS emergency-call-function-deactivated message and a loss of connection to the mobile network operator (AT&T).B13BCF2Verified diagnostic recordB101C07Verified diagnostic recordB200042Verified diagnostic recordB200047Audi DTC B200047 means “control unit faulty.” Verified Audi bulletins show that, in specific applications, it can be caused by diagnostic/software behavior rather than a failed module. The exact affected system depends on the stored symptom code and control-module address.C12EB92For verified applicable Audi vehicles, DTC C12EB92 is addressed by replacing the laser scanner control module J1122 according to the repair manual, then checking its software version. If the software is below version 0205, the Audi bulletin directs a software update; version 0205 requires no further action.C12EBF1C12EBF1 indicates a malfunction reported for the laser used by Adaptive Cruise Assist. For specified U.S. Audi applications, Audi service communications identify a laser-scanner control-module software issue and prescribe a software update.U122800For a 2019–2020 US Audi e-tron, DTC U122800 means “Driver door control unit implausible.” Audi service communications identify a software update as the technical background for this condition.B14FF29For applicable 2019–2020 US Audi e-tron vehicles, B14FF29 is identified in Audi manufacturer communications as “Motor for child lock, implausible signal.” Audi states that the software needs to be updated.P060C00Verified diagnostic recordP000000For the verified Audi e-tron applicability, P000000 is documented as a passive/sporadic DTC in the suspension control module (J775, address 0074). When it is the described stored DTC and no further DTCs are present in other control modules, Audi’s service instruction is: do not repair or replace.U12B800Verified diagnostic recordB16D5F6DTC B16D5F6 means “Tail light cluster, left 2, number plate light faulty.” Verified applicability is limited to the 2019 Audi e-tron in the US.B16D5F1B16D5F1 indicates: “Tail light cluster, left 2, LED faulty.” Verified applicability is the 2019 Audi e-tron (US).B16D7F2B16D7F2 is an Audi DTC meaning: “Right rear tail lamp 2 Tail lamp faulty.” Verified evidence identifies it in the comfort system central control module J393 (address word 0046).B16D7F6For a 2019 Audi e-tron in the US, DTC B16D7F6 means: “Tail light cluster, right 2, number plate light faulty.”B16D7F1Audi DTC B16D7F1 means: “Tail light cluster, right 2, LED faulty.” Verified evidence identifies it as a rear-lighting fault for the 2019 Audi e-tron in the US.B16DF52For a 2019 US Audi e-tron, DTC B16DF52 is documented in Audi TSB 91 20 42 as occurring with a trunk-lid taillight that does not work or flickers. The supplied evidence does not establish driving or charging safety status.B16D5F2Audi DTC B16D5F2 means “Left rear tail lamp 2 Tail lamp fault.” Verified Audi service information associates it with a trunk-lid taillight LED strip that may flicker or may remain partly illuminated after the ignition is switched off.B107BF0Audi DTC B107BF0 with symptom 233479/233523 indicates temporary partial system availability caused by environmental influence, such as an external ultrasound signal, a street sweeper, or construction equipment.B10FCF0Audi DTC B10FCF0 is documented as a temporary partial-system availability condition associated with environmental influences, including external ultrasound signals such as those from a street sweeper or construction equipment.C12B3FDAudi DTC C12B3FD with symptom code 221284 is documented as a temporary visibility restriction detected by the front camera for driver-assistance systems. The cited Audi communications state that it is logged when the camera recognizes a restriction for more than 77 seconds.U112100Audi DTC U112100 means “data bus, missing message.” Verified evidence links it to more than one system context, including adaptive air suspension and the high-voltage battery charger control module. The code alone does not establish a single failed part or whether the vehicle is safe to drive or charge.C1260F0Audi DTC C1260F0 means: “compressor control unit for adaptive suspension, no communication.” Verified Audi service information associates it with an air-suspension malfunction warning and directs inspection of relevant wiring and connector contacts.U101400For the listed Audi vehicles, U101400 may be stored in telematics control module J949 (address word 0075) because of a start-up timing issue. Audi’s communication states that no repair is available and repairs should not be performed for this concern.P0CE100For a 2020 Audi Q5 in the US, DTC P0CE100 is documented in Audi service communications as a code that may be stored in the thermal management control module. Audi’s documented production solution is updated software for thermal management control module J1024 (address word 00C5).P0C4300For a verified applicable vehicle, this Audi service information links DTC P0C4300 to a condition addressed by updated software for the thermal management control module (J1024, address word 00C5).B127E4BFor Audi A7, A8, and e-tron vehicles (model years 2019–2022, US), DTC B127E4B is listed in an official Audi/NHTSA manufacturer communication for the right overhead-view camera. The communication specifically states that replacing the driver-assistance systems control module (J1121) is not effective for the listed DTCs.B127C04Audi DTC B127C04 is listed in an official Audi/NHTSA manufacturer communication for the front overhead-view camera. The supplied evidence does not establish the complete diagnostic meaning beyond the truncated title/meaning, “Replacing the c.”C12AE02Audi DTC C12AE02 is documented in an official Audi/NHTSA service communication concerning the overhead-view camera system. The supplied evidence does not establish a complete fault description beyond the title fragment “Replacing the control m.”C12B002Audi DTC C12B002 is listed in an official Audi/NHTSA manufacturer communication concerning the left overhead-view camera. The communication states that replacing the driver-assistance systems control module J1121 is not effective for this DTC scenario.C12AF02C12AF02 is listed in an official Audi/NHTSA manufacturer communication concerning the control module for driver assistance systems (J1121). The supplied evidence does not establish the full code description, vehicle symptoms, driving/charging safety, or a specific repair outcome.B127F04Audi DTC B127F04 is listed in an official Audi/NHTSA manufacturer communication for affected 2019–2022 US A7, A8, and e-tron vehicles. The communication states that replacing the driver-assistance control module J1121 is not effective for the referenced DTCs.B127F4BAudi DTC B127F4B is listed in an official Audi/NHTSA manufacturer communication concerning the right overhead-view camera. The communication states that replacing the driver-assistance systems control module J1121 is not effective for this DTC group.B127E04For Audi A7, A8, and e-tron vehicles (2019–2022, US), DTC B127E04 is listed in an Audi manufacturer communication in connection with the left overhead-view camera. The communication states that replacing the driver-assistance systems control module (J1121) is not effective for the listed DTCs.B127C4BAudi DTC B127C4B is documented in an official Audi communication as a fault associated with the front overhead-view camera. The supplied evidence also states: “Replacing the control module fo” (text is truncated in the verified record).B200FFAFor certain 2019–2022 US Audi models, B200FFA may be stored in the driver assistance systems control module J1121 as an internal malfunction with symptom code 282648 or 282649. Audi’s published service information states that replacing J1121 for the listed DTCs is not effective.C12B102For Audi C12B102, verified evidence says replacing the driver-assistance control module J1121 is not effective for the listed DTC condition. The supplied bulletin evidence identifies C12B102 in connection with the right overhead-view camera.B127D4BAudi DTC B127D4B is identified as “Replacing the control module for driver assistance systems (J1121) for the above.” Verified evidence links it to the left overhead-view camera diagnostic group in a 2020 Audi manufacturer communication.B127D04Verified diagnostic recordB200000Audi DTC B200000 means “Ctrl. Module Faulty.” For the verified 2021 US Audi A7, A8, Q5, and e-tron applications, Audi documentation identifies it in telematics control module J949 (address 0075) with symptom code 131096. Audi states it can be stored erroneously when transport mode is removed.B200096Verified diagnostic recordLane change and exit warning: Malfunction! Please contact service.For certain 2020–2021 US Audi A7, A8, and e-tron vehicles, this message is documented in Audi manufacturer communications as occurring with sporadic failure of intersection/lane-changing assist. Audi directs service diagnosis; the supplied evidence does not establish whether the vehicle is safe to drive or charge.Audi pre sense: Malfunction! Please contact service.For certain 2020–2021 US Audi A7, A8, and e-tron vehicles, this message is documented in Audi service communications in connection with a sporadic intersection/lane-changing assist failure. Contact Audi service for diagnosis.Rear intersection assistant: Malfunction! Please contact service.For supported 2020–2021 US Audi A7, A8, and e-tron vehicles, this alert is documented in Audi communications as a sporadic failure of intersection/lane-changing assist. Contact Audi service for diagnosis.Intersection assist Malfunction! Please contact service.For certain 2020–2021 US Audi A7, A8, and e-tron vehicles, this alert is documented in Audi manufacturer communications as a sporadic intersection/lane-changing assist failure. Audi directs service diagnosis; the supplied evidence does not establish whether the vehicle is safe to drive or charge.Parking Aid: Malfunction!Verified diagnostic recordB107A16Verified diagnostic recordAdaptive driving assist: limited availability, see ownerFor applicable 2019–2021 US Audi A8 and e-tron vehicles, this alert can appear when dirt restricts the laser scanner’s detection capability. Certain driver-assistance features might then be unavailable.C1106F0For a 2019 US Audi e-tron, DTC C1106F0 may be stored in the laser scanner control module J1122 (address 00CD) when Adaptive Cruise Assist is unavailable. NHTSA-published Audi communication 10185262 identifies the DTC as “Dynamic calibration limit exceeded” with symptom code 11575304.Drive faultVerified diagnostic recordU103100For certain US Audi e-tron and e-tron Sportback vehicles, DTC U103100 may be stored sporadically in the ABS control module and is addressed by an ABS control-module software update.Traffic Jam Assist: malfunction!Audi’s “Traffic Jam Assist: malfunction!” alert is a verified instrument-cluster malfunction indication. An Audi technical service bulletin (TSB) documents it together with possible stored faults involving the front camera R242 and distance regulation control module J428.Audi Active Lane Assist: malfunction!Verified diagnostic recordB11E201For certain 2019–2020 Audi A8 and e-tron vehicles in the US, DTC B11E201 means “Video line 2 for night vision system.” Audi documentation says instrument-cluster tolerances can cause an erroneous wiring-problem detection.B11E101For certain 2019–2020 US Audi A8 and e-tron vehicles, DTC B11E101 relates to the night vision system video line. Audi states that instrument-cluster tolerances can incorrectly detect a wiring fault when the relevant wiring has been checked and found good.SOS – Emergency call malfunction, please contact serviceFor certain 2021 US Audi models, this instrument-cluster message is covered by Audi manufacturer communications concerning the emergency-call module and communication unit. Contact Audi service for diagnosis.Electrical system: fault. Safely stop vehicleVerified diagnostic recordB126CF0B126CF0 indicates that the Audi navigation database is malfunctioning. Verified Audi service information links it to a navigation map over-the-air update that was interrupted by an internal reset, leaving the database corrupted.P31CF00P31CF00 is an Audi DTC defined as “Charge cover A recognition cover locking.” Verified evidence lists it in Audi manufacturer communications for certain US-market 2020–2021 e-tron vehicles.B1A8604B1A8604 means “Function button charge door 1 faulty.” Verified Audi communications associate it with a defective charging-flap function button and, in some cases, a charging flap that cannot be opened.B1A8704Audi DTC B1A8704 means “Function button charge door 2 faulty.” Verified Audi manufacturer communications list it for certain US-market 2020–2021 Audi e-tron vehicles.U15AB00For applicable U.S. 2020–2021 Audi e-tron vehicles, DTC U15AB00 is identified in an Audi manufacturer communication as “Fast battery charging (DC) Communication.”P31E700P31E700 is an Audi DTC defined as “AC power supply cable Open circuit.” Verified evidence lists it for US-market 2020–2021 Audi e-tron vehicles.U13AE00For certain US-market 2020–2021 Audi e-tron vehicles, DTC U13AE00 is identified as “Active parking system control module.” Audi service communications list it as a DTC that may be stored in the high-voltage battery charger control module (OBC), J1050, address word 00C6.U15AC00For certain US-market 2019–2021 Audi e-tron vehicles, U15AC00 means “Signal damping log Malfunction.” Audi documentation states that after a specified flashing procedure, U15AC00 can be stored statically due to a diagnostic flaw and cannot be erased; in that specific post-flash context, Audi says it may be ignored.U15B500Audi DTC U15B500 is identified in verified Audi communications as “Fast battery charging (DC) Charging station.” It is documented for US-market 2020–2021 Audi e-tron vehicles.P1A1500Audi DTC P1A1500 means “Charging unit 2 Function restriction.” Verified evidence lists it in Audi charging-related manufacturer communications.B129C11Verified diagnostic recordB239C11Verified diagnostic recordB129B11Verified diagnostic recordB16D4F4Audi DTC B16D4F4 means “left tail lamp 1 Turn signal light defective.” For certain US Audi A8 and e-tron vehicles, Audi technical bulletins describe a warning message even though the turn signals remain functional; the documented technical background is a timing issue in tail-lamp software.B16D6F4For applicable 2019–2020 US Audi e-tron vehicles, DTC B16D6F4 means “Right tail lamp 1 Turn signal light defective.” Audi technical communications document that a tail-lamp software timing issue can set this code while the turn signals remain functional.B16D5F4Verified diagnostic recordB16D7F4For applicable 2019–2020 US Audi e-tron vehicles, DTC B16D7F4 means “Right tail lamp 2 Turn signal light defective.” Audi documentation states that the turn signals remain functional and identifies a timing issue in tail-lamp software as the technical background.B14BF01For covered Audi vehicles, DTC B14BF01 is documented in Audi service communications as a steering-column vertical-adjustment motor electrical error, with symptom code 66145. The documented correction is a software update followed by clearing the control unit.B170AF1Audi DTC B170AF1 means “Coding Step 2 not carried out.” Verified Audi communications associate it with the driver assist systems control module J1121 (address 00A5), including after a software update. The specified action is to run the ODIS test plan calculated for B170AF1.U110100For the Audi applications covered by the verified bulletin, U110100 may be an erroneously stored “ghost DTC” in the driver-assistance systems control module. Audi states that it does not cause functional problems or visible warning messages, and repairs should not be performed for that concern.C12D7F0C12D7F0 is an Audi driver-assistance DTC meaning “Emergency assistant Status feedback for HMI implausible.” Verified evidence identifies an update needed to a parameter setting/coding in the driver assistance systems control module J1121 (address word 00A5).B157811Verified diagnostic recordB157629Audi DTC B157629 means: Hall sensor 2 for the roof blind motor has an implausible signal. Verified applicability is 2020–2021 Audi A8 models in the US.P0CA400Audi DTC P0CA400 means “Hybrid/EV Battery Charging Voltage High.” Verified Audi/NHTSA bulletin evidence lists it in connection with interrupted communication at certain DC chargers, which can temporarily suspend charging and may also produce AC charging communication errors.B194B13For 2021–2022 US Audi e-tron vehicles, DTC B194B13 may be stored in the high-voltage battery charger control module J1050 (address 00C6) with symptom code 3211295. The verified NHTSA manufacturer communication states it may be found during PDI or other diagnostic work with no customer concerns.U15C900Verified diagnostic recordP31D100Verified diagnostic recordB1A8AF0For 2021–2022 Audi e-tron Sportback vehicles in the US, B1A8AF0 may be stored in the high-voltage battery charger control module (J1050, address 00C6). Audi’s referenced communication states it can be found during PDI or other diagnostic work with no customer concerns reported.Electrical system: fault. Please contact workshopVerified diagnostic recordP0A9500Verified diagnostic recordU122C00For certain 2019–2020 US Audi A8 and e-tron vehicles, U122C00 can be stored in the Gateway (J533) when the emergency call module and communication unit (ConBox, J949) temporarily stops communicating with the vehicle due to a sporadic startup issue.U142100Audi DTC U142100 means the gateway cannot communicate with the emergency call module and communication unit (ConBox). Verified Audi bulletins associate it with an SOS malfunction message on certain vehicles and identify specific startup or transport-mode situations in documented cases.U164200Audi DTC U164200 means “Ethernet Emergency Call Module no communication.” For verified 2019–2020 US Audi A8 and e-tron applications, Audi service communications associate it with an SOS malfunction message and a temporary loss of communication with the emergency call module and communication unit (ConBox), J949.P33EB00P33EB00 means “Battery management system check DTC memory.” Verified evidence links it to charging-communication issues on certain 2020–2021 Audi e-tron vehicles in the US.C12BB00C12BB00 is identified by Audi as “Control motor.” Verified evidence links it to a condition in which certain DC chargers can interrupt charger-to-vehicle communication, temporarily suspending charging.B191CF8B191CF8 is an Audi DTC meaning “Charge door communication malfunction.” Verified evidence links it to interrupted communication between certain DC chargers and the vehicle.U15BF00Verified diagnostic recordU002800For a 2020 Audi Q5 in the US, DTC U002800 means “Vehicle Communication Bus A.” An official Audi/NHTSA service communication lists it among possible stored faults when warning lamps are illuminated and/or the vehicle cannot be driven.P0A2F00P0A2F00 means “Drive Motor ‘A’ Over Temperature.” Verified evidence applies this information to the 2020 Audi Q5 in the US.U011000U011000 means “Lost Communication With Drive Motor Control Module.” Verified Audi evidence links this DTC to specific conditions in certain U.S. Audi vehicles, including a documented software issue and, in a separate bulletin, possible chafing of a 12V power-electronics wiring harness against underbody trim.U002900For a 2020 Audi Q5 in the US, DTC U002900 means “Vehicle Communication Bus A Performance.” An Audi/NHTSA manufacturer communication lists this code among possible stored faults in a condition involving power-electronics-related faults. The source does not establish whether the vehicle is safe to drive or charge.U140500Audi DTC U140500 means “Terminal 15 Implausible signal.” Verified evidence links it to specific Audi service bulletins, but driving, charging, and overall severity are not yet established by verified evidence.P0A1B00P0A1B00 is an Audi DTC meaning “Drive motor ‘A’ Control Module.” Verified Audi bulletins associate it with Electric Drive 2 (J944, address 00CE) on certain vehicles and describe several distinct bulletin-specific scenarios; a code alone does not establish one cause.U121C00For a 2020 Audi Q5 in the US, DTC U121C00 means “Drive Motor ‘A’ No Communication.” Audi’s official service communication identifies possible chafing of the 12V wiring harness for the power electronics (J841, address word 0051) against underbody trim as the technical background for a bulletin that includes this DTC.U003600For a 2020 Audi Q5 in the US, DTC U003600 is documented in an Audi/NHTSA manufacturer communication as “Vehicle Communication Bus A (-) shorted to Bus A (+).” It may occur with multiple warning lamps and, in some cases, a vehicle that cannot be driven.C119911For a 2021 Audi e-tron in the US, C119911 is documented in an Audi/NHTSA manufacturer communication as a headlight-related fault: “High beam bulb, short circuit to ground.” The communication says headlight operation is not affected and attributes the stored code to overly sensitive diagnostic software.U059B00Verified diagnostic recordP0AC000Verified diagnostic recordP33F000Verified diagnostic recordAudi pre sense: fault. Please contact workshop.This Audi alert is verified in an official NHTSA-posted Audi manufacturer communication for certain 2020–2023 US Audi A7, A8, and e-tron vehicles. The communication associates the message with inoperative intersection/lane-change assistance functions and a possible radar-sensor calibration fault.Rear cross-traffic assist: fault. Please contact workshop.This Audi alert indicates a fault affecting rear cross-traffic assist. The verified Audi service evidence directs contacting a workshop.Side assist and exit warning system: fault. Please contact workshop.Audi identifies this message as a fault condition in which intersection/lane-change assist may be inoperative. An Audi workshop should evaluate it; driving and charging status are not established by the verified evidence.Intersection assist: fault. Please contact workshop.Audi identifies this as an intersection/lane-change assist malfunction message. Official Audi technical bulletins say the affected assist functions may be inoperative and instruct workshop diagnosis.C12BFF0C12BFF0 indicates that automatic calibration of an Audi radar sensor was not possible. Verified Audi service information says this can occur when the calculated dynamic angle offset exceeds ±5° during continuous calibration while driving above a defined speed threshold.C12B3FBVerified diagnostic recordC1399F0Audi DTC C1399F0 indicates that brake application mode is active during a brake-pad/disc break-in process. In the verified Audi material, the DTC is logged in the ABS control module and is automatically deactivated when the required energy amount is reached.B126CF1Audi DTC B126CF1 means “Navigation database not available.” Verified Audi/NHTSA communications associate it with a navigation system that remains initializing or has a corrupt or incomplete map after an over-the-air update. The cited bulletin applies only in combination with recall 91DZ.Audi pre sense: fault. Please contact service.Verified diagnostic recordSide assist and exit warning system: fault. Please contact service.This Audi alert indicates a fault affecting the side assist and exit warning system. Official Audi technical-service communications document this message in connection with sporadically inoperative lane change assist/intersection assist on certain vehicles.Intersection assist: fault. Please contact service.For verified 2020–2021 U.S. Audi A7, A8, and e-tron applicability, this instrument-cluster alert indicates a reported intermittent malfunction of intersection assist/lane-change assist. Official Audi communications direct the customer to contact service.Rear cross-traffic assist: fault. Please contact service.Audi has documented this message as a possible sporadic lane-change/intersection-assist complaint on certain 2020–2021 US A7, A8, and e-tron vehicles. The message itself directs the driver to contact service.P0AA500Audi DTC P0AA500 is identified in verified Audi service information as “Hybrid/EV Battery Negative Contactor Circuit Stuck Open.” For the specified condition, Audi states not to proceed according to GFF, which may suggest replacement of the high-voltage battery switching unit/Battery Junction Box (SX6).P0AA200Verified diagnostic recordB16D531For applicable 2020–2021 US Audi e-tron vehicles, DTC B16D531 means “Left tail lamp 2, no signal/open circuit.” Audi’s published service information identifies overly sensitive tail-lamp diagnostic software as the technical background and states that updated tail-lamp software is available.B16D431For certain 2020–2021 Audi e-tron vehicles in the US, DTC B16D431 identifies “Left tail lamp 1, no signal/open circuit.” Audi’s published service information attributes this condition to tail-lamp diagnostic software that is too sensitive and states that updated software is available.B16D731B16D731 means “Right tail lamp 2, no signal/open circuit.” Verified Audi/NHTSA evidence identifies overly sensitive tail-lamp diagnostic software as the technical background for this DTC in the covered vehicles.B16D631For certain 2020–2021 Audi e-tron vehicles in the US, DTC B16D631 means “Right tail lamp 1, no signal/open circuit.” Audi documented that tail-lamp diagnostic software sensitivity can store this code and cause rapid instrument-cluster turn-signal flashing. Updated tail-lamp software is available.C10AC07Verified diagnostic recordB122B13Audi DTC B122B13 is identified in the verified manufacturer communications as “Central locking motors Open circuit.”B12CC15For a 2020 Audi Q5 PHEV in the US, DTC B12CC15 is identified in an Audi/NHTSA manufacturer communication as: right back-up light bulb open circuit/short circuit to B+. The bulletin associates it with a tail-lamp warning in the instrument cluster.B12CB15For a 2020 Audi Q5 in the US, DTC B12CB15 is documented as a left back-up light bulb circuit fault: “Open circuit/short circuit to B+.” Audi’s bulletin describes a possible reverse-lamp internal circuit-board separation in the rear-bumper lamp.B113E29B113E29 is documented by Audi service communications as “Closing assistance Range/Performance” in the rear lid control module J605 (address 006D). It is associated with a power rear lid that may not close completely or latch in the secondary position.B101D29B101D29 indicates an implausible signal from the front passenger-side safety-belt switch. Verified evidence associates it with an illuminated airbag warning light and storage in the airbag control module (J234, address word 0015).B101C29B101C29 is an Audi airbag-system DTC meaning “Driver seat belt switch implausible signal.” Verified evidence links it to an illuminated airbag warning light on certain US-market 2021–2022 Audi A7 PHEV vehicles.P060700Verified diagnostic recordP31C500Verified diagnostic recordB200049Verified diagnostic recordU131C00Verified diagnostic recordB2F0100Verified diagnostic recordU112200Audi DTC U112200 is identified in verified manufacturer communications as “Data bus implausible message.” In the cited condition, it may be stored as static with symptom code 303616. Static DTCs cannot be erased; intermittent DTCs may erase but return when the condition recurs.U012700U012700 is documented by Audi as “Tire Pressure Monitoring Control Module - no Communication” with symptom code 358656 (static).U112300Verified diagnostic recordU110300For specified 2021–2022 US Audi models, DTC U110300 is identified in Audi service communications as “Production mode active” in the telematics control module J949 (address word 0075). Audi directs technicians to run the control-module replacement test plan through ODIS Guided Functions, without replacing the module.Maneuver assist: faultFor certain US 2022–2023 Audi e-tron GT and RS e-tron GT vehicles, an instrument-cluster message may briefly display: “Maneuver assist: fault. Please contact service.” Audi’s verified service communication states that no repair is available and instructs technicians not to perform repairs for this concern.Rear spoiler: Malfunction!Verified diagnostic recordAudi adaptive light malfunction“Audi adaptive light malfunction” is an Audi instrument-cluster warning documented in Audi technical service communications. In the verified examples, it can appear with temporarily inoperative driver-assistance systems that become available again after a few seconds.B200043For verified 2022 US Audi e-tron GT and RS e-tron GT applicability, DTC B200043 means “Control Module Faulty.” Audi’s cited technical service bulletins identify a software bug in the head-up display (HUD) as the technical background when this code is stored in HUD control module J898 (address word 0082).P1D6C00For 2022 US Audi e-tron GT and RS e-tron GT, P1D6C00 means “12V battery faulty.” Verified Audi/NHTSA bulletin evidence states that, when stored intermittently in gateway J533 (address 0019), it is caused by a gateway software error, does not affect vehicle operation, and requires no action or repair.C103407For U.S. 2021–2022 Audi A7 vehicles, DTC C103407 is identified in the supplied official Audi/NHTSA communication as: “Left front level control system sensor mechanical malfunction.” The communication asks technicians to contact Audi Technical Assistance Center (TAC) before replacing parts.C104807For certain U.S. 2021–2022 Audi A7 vehicles, DTC C104807 may be stored in suspension control module J775 (address word 0074) with a suspension malfunction warning shown in the instrument cluster. The supplied official communication describes C104807 as “Level control system sensor mechanical malfunction.”B18AC13B18AC13 is an Audi DTC meaning: “Motor for rear spoiler drive 1, Open circuit.” Verified Audi service information identifies a possible loss of contact inside the rear spoiler drive motor that can cause intermittent or permanent rear-spoiler operation loss.B16F8F1B16F8F1 indicates “Rear spoiler drive 1, Blocking when extending.” Verified Audi service-bulletin evidence links this DTC to rear-spoiler operation concerns on certain US-market 2021–2022 Audi A7, e-tron GT, and RS e-tron GT vehicles.Instrument cluster: malfunctionVerified diagnostic recordP1A37Verified diagnostic recordP0AA100For a 2022 Audi e-tron GT in the US, DTC P0AA100 means “Hybrid/EV Battery Positive Contactor Circuit Stuck Closed.” Audi’s verified service-bulletin evidence lists this code, but does not establish symptoms, root cause, driving/charging status, or a repair procedure in the supplied evidence.P1D6500For a 2022 Audi e-tron GT in the US, DTC P1D6500 is identified in an official Audi/NHTSA manufacturer communication as: “Hybrid/high-voltage battery controller for battery cells insufficient cell voltage.”P0AE3For a 2022 Audi e-tron GT in the US, DTC P0AE3 is listed in Audi/NHTSA manufacturer communication 93 21 60 (2065473/1) among multiple Hybrid Battery Management DTCs. The supplied evidence does not establish a standalone generic definition for P0AE3, its driveability, charging status, or a specific repair.P0AA1P0AA1 is listed in an Audi technical service bulletin for the 2022 e-tron GT (US). The bulletin concerns various high-voltage-system or vehicle concerns after ignition-on, but the supplied evidence does not establish the exact fault meaning, driveability, charging status, or repair for P0AA1 alone.P1D65For certain US Audi e-tron GT and RS e-tron GT vehicles, DTC P1D65 is included in Audi TSB 2065473 for Hybrid Battery Management. The bulletin directs a software-level check of the J840 control module and, when applicable, performance of the specified Audi TSB procedure.P0AA400P0AA400 means “Hybrid/EV Battery Negative Contactor Circuit Stuck Closed.” Verified applicability is the 2022 Audi e-tron GT in the US.P160900For a 2022 Audi e-tron GT in the US, verified Audi/NHTSA service-bulletin evidence identifies P160900 as “Crash shut-off was triggered” when stored in the Hybrid Battery Management (BECM), J840 (address word 008C).P0AA5Verified diagnostic recordP0AE300P0AE300 is identified in an official Audi/NHTSA service communication as “Hybrid/EV Battery Precharge Contactor Circuit Stuck Open.” The verified applicability is the 2022 Audi e-tron GT in the US.P1A01Verified diagnostic recordP0AE2For a 2022 Audi e-tron GT (US), DTC P0AE2 is listed in Audi/NHTSA manufacturer communication 93 21 60 / 2065473/1 concerning multiple Hybrid Battery Management fault codes. The supplied evidence does not provide the complete fault definition or a confirmed repair for P0AE2 alone.P168A00For a 2022 US Audi e-tron GT, DTC P168A00 is identified in an official Audi/NHTSA service communication as “Reversible crash shut-off was triggered.”P0AA4Verified diagnostic recordP0AA2Verified diagnostic recordP1D5FFor a 2022 Audi e-tron GT in the US, DTC P1D5F is listed in Audi Technical Service Bulletin 93 21 60 / 2065473/1 among 93 Hybrid Battery Management fault codes. The supplied evidence does not establish a code-specific definition, root cause, repair, driving status, or charging status for P1D5F alone.P1D5F00For a 2022 Audi e-tron GT in the US, DTC P1D5F00 is identified in an official Audi/NHTSA manufacturer communication as: “Hybrid/high-voltage battery controller for battery cells cell voltage too high.”P168AVerified diagnostic recordP1A0100For a 2022 Audi e-tron GT in the US, DTC P1A0100 is identified in an official Audi/NHTSA manufacturer communication as “Crash signal monitoring failed.”P1A3700Audi DTC P1A3700 is identified in verified Audi/NHTSA service information as: “Controller for cells of high voltage/hybrid battery electrical error.”P0AE200For a 2022 US Audi e-tron GT, DTC P0AE200 is identified in an official Audi/NHTSA service communication as “Hybrid/EV Battery Precharge Contactor Circuit Stuck Closed.”P1609For a 2022 Audi e-tron GT (US), P1609 is listed in an Audi/NHTSA manufacturer communication concerning multiple Hybrid Battery Management fault codes. The supplied evidence does not establish a standalone definition, severity, driving status, charging status, or repair for P1609.B200FF0Audi DTC B200FF0 means “Internal malfunction.” Verified Audi bulletins show it can be stored either in the suspension control unit J775 or in the instrument cluster J285, depending on the applicable bulletin and vehicle condition.B17D900For a 2022 US Audi e-tron GT, DTC B17D900 is documented in an Audi manufacturer communication as a Hybrid Battery Management (BECM/J840) safety-controller software issue associated with intermittent no-start complaints. The documented service action is an SVM software update after the concern and DTC are confirmed.U13EB00U13EB00 is an Audi DTC meaning “Emergency call module and communication unit Flight mode activated.” Verified Audi bulletins associate it with the emergency-call/communications module at address 0075.P169A00Audi DTC P169A00 means “Transport mode active.” Verified Audi service communications state that the communication unit (ConBox) can remain in transport/flight mode when it is not taken out of transport mode with a VAS 6154 diagnostic interface.Air suspension: system faultAudi OEM alert: “Air suspension: system fault.” Verified Audi technical-service communications link this instrument-cluster message to faults recorded in the suspension control unit J775 (diagnostic address 0074) on specified US-market vehicles.B200FF1For certain 2019–2023 US Audi A7, A8, Q5, and e-tron vehicles, DTC B200FF1 is documented by Audi as an “Internal malfunction” in the suspension control unit J775 (address 0074).B200FF4Audi DTC B200FF4 is documented as “Internal malfunction” in the suspension control unit J775 (address 0074).B126101Verified diagnostic recordB126113Audi DTC B126113 means “Windshield washer pump Open circuit.” Verified evidence links it to an inoperative washer system and/or windshield-washer solvent leak, with the DTC stored in the BCM/J519 control module.B126111B126111 indicates a short circuit to ground reported for the windshield washer pump. Audi’s verified bulletin states that a blocked washer pump caused by frozen washer fluid can increase pump resistance and store this DTC; it may be static or sporadic.U178A00Verified diagnostic recordP215C00P215C00 is documented by Audi as an output-shaft-speed/wheel-speed correlation fault when specific related drivetrain-control faults are also stored. Verified applicability is limited to U.S. 2022 Audi e-tron GT and RS e-tron GT vehicles.U041100Verified diagnostic recordC110300Verified diagnostic recordB107B13B107B13 is documented by Audi/NHTSA manufacturer communications as “Rear parking aid sensor Open circuit.” For a 2022 US Audi Q3, the verified bulletin evidence associates this code with a rear parking-distance-control (PDC) sensor connector that is not fully seated.B13034AVerified diagnostic recordB131D29For US-market 2022–2023 Audi Q4 e-tron vehicles, B131D29 is documented in an Audi Technical Service Bulletin as: “Sirens / alarm horn for anti-theft warning system, implausible signal.” The bulletin states it may be found during pre-delivery inspection (PDI) or other diagnostic work with no customer concerns reported.B114DF2For U.S. 2022–2023 Audi Q4 e-tron vehicles, Audi TSB 00 22 59 (2067842/1), dated August 23, 2022, documents DTC B114DF2 as a possible stored fault found during PDI or other diagnostic work, with no customer concerns stated in the bulletin evidence.C110B54For a 2022 Audi Q4 e-tron in the US, DTC C110B54 is referenced in an Audi/NHTSA manufacturer communication under Adaptive Cruise Control. The documented procedure includes running the radar sensor replacement test plan and a radar sensor adjustment as applicable.B18B0F2For a 2022 Audi Q4 e-tron in the US, B18B0F2 is documented in an Audi manufacturer communication as a Data Bus On-Board Diagnostic Interface (ICAS) self-diagnosis item. The communication specifies locking and unlocking SFD as part of the diagnostic operation.B184C00For a 2022 Audi Q4 e-tron in the U.S., DTC B184C00 is documented in an Audi manufacturer communication as requiring the Guided Fault Finding (GFF) “VKMS adaption” test plan, labor operation 0150 0000. The diagnostic-protocol time is allowed up to 25 TU.P05A000P05A000 indicates that the ECM has stored “Active Grille Air Shutter ‘A’ Stuck.” Verified Audi/NHTSA manufacturer communications associate this with an illuminated check-engine lamp on applicable vehicles.P0A7D00P0A7D00 is documented by Audi as “Hybrid/EV Battery Pack State Of Charge Low” for vehicles with a 48 V electrical system. The referenced Audi communication states that the 48 V battery may enter a low-voltage protection state and will not accept a charge.P05FF00For certain 2022–2023 US Audi e-tron GT and RS e-tron GT vehicles, DTC P05FF00 may be stored in the ABS/ESC control module when low-speed braking produces brake-pedal vibration/pulsation or an unusual pedal feel. Audi’s documented production solution was under analysis.P023700P023700 is listed in the supplied Audi material as “Turbocharger Boost Sensor (A) Circ. Low Input.” The verified Audi workshop material associates it with the 2022 Audi Q3 2.0 TFSI—not the supplied e-tron or e-tron GT applicability entries.P023600Verified diagnostic recordP010600P010600 is recorded as “Manifold Abs. Pressure or Bar. Pressure Range/Performance.” The supplied evidence does not establish this code’s EV-specific meaning, severity, driving safety, charging safety, or repair for Audi e-tron/e-tron GT vehicles.P023800P023800 is identified in the verified Audi material as “Turbo charger boost sensor (a) circ. high input.” The supplied official documentation applies this diagnostic worksheet to the 2022 Audi Q3 2.0 TFSI, not to an electric e-tron model.B10F914B10F914 is identified in the supplied Audi manufacturer communications as: right front center parking aid sensor—open circuit/short circuit to Ground (GND) may be set. The evidence supplied does not establish applicability to Audi e-tron or e-tron GT, despite the supplied applicability records.Electrical system malfunction! Please contact ServiceVerified diagnostic recordElectrical system faultVerified diagnostic recordElectric drive: fault. Please contact workshopFor applicable US-market 2022–2024 Audi Q4 e-tron vehicles, this alert is documented in Audi technical service bulletins as occurring with fault codes stored in the Hybrid Battery Management control unit. Contact an Audi workshop for diagnosis.P18F100Verified diagnostic recordP060600Verified diagnostic recordP0CFF00For a 2022 Audi Q4 e-tron in the US, DTC P0CFF00 is documented by Audi as “Hybrid/EV Battery Pack Coolant Pump Stuck.” It is covered in an Audi technical service bulletin context together with battery-coolant-pump-related DTCs.P2B2800P2B2800 is identified in an Audi technical service bulletin as “Hybrid/EV Battery Pack Coolant Pump Performance.”P0C4A00For a 2022 Audi Q4 e-tron (US), DTC P0C4A00 is documented by Audi in Hybrid Battery Management (BMCe) J840 as “Activation of coolant pump 1 for hybrid / high voltage battery malfunction.” Audi’s bulletin associates it with the dash warning: “Electric drive: fault. Please contact workshop.”P251500P251500 is an Audi thermal-management DTC for an electrical fault in refrigerant pressure sensor 2. Audi documentation links it to loss of pressure evaluation and reports that cabin air conditioning may not cool, sometimes intermittently.P053000For certain 2020–2022 U.S. Audi models, DTC P053000 indicates an air-conditioning system pressure-sensor electrical fault. Audi’s bulletin links it to loss of cabin cooling, which may be intermittent.B1A9913For affected 2023–2024 US Audi e-tron GT and RS e-tron GT vehicles, DTC B1A9913 may be an erroneous software-related “ghost DTC.” Audi states it has no effect on vehicle functionality and that no repair is available at this time.U014600Verified diagnostic recordU14A00Audi DTC U14A00 is identified as “Terminal 30.” Verified NHTSA-hosted Audi manufacturer communications state that this code may be stored in the ECM. Its driving, charging, and service urgency are not yet established by verified evidence supplied.Lane departure warning faultFor certain 2022–2024 Audi e-tron GT and RS e-tron GT vehicles in the US, “Lane departure warning fault” may appear at vehicle start. Audi’s official service communication associates this condition with diagnostic trouble codes stored in the steering control unit J500.Fault: Limited warning messages...Verified diagnostic recordInstrument cluster: fault. Limited warning messages. Please contact workshopVerified diagnostic recordVehicle sound: Malfunction! Pedestrians cannot hear vehicle. Please contact ServiceVerified diagnostic recordAntenna MalfunctionFor certain 2023 Audi US models, an “Antenna Malfunction” message can be displayed on the MMI screen. Audi manufacturer communications link this message to a possible communication issue involving the emergency call module and communication unit.Engine start system: faultFor covered Audi vehicles, this alert can appear with no functional issues. Audi technical-service communications associate it with a stored Comfort Control Module fault combination and provide a service procedure. Driveability and charging safety are not established by the supplied evidence.Power unit start system: faultVerified diagnostic recordmaneuver assist: fault. Please contact serviceFor applicable 2022–2023 Audi e-tron GT and RS e-tron GT vehicles in the US, this message can briefly appear if a gear is selected immediately after the drive system is activated, before relevant network control units have finished initializing.Electric drive: fault. Please contact “ServiceVerified diagnostic recordEmergency call function: fault. Function partially available. Please contact serviceFor 2022–2024 Audi Q4 e-tron vehicles in the US, this instrument-cluster message is documented in an official Audi manufacturer communication. It indicates a fault affecting the emergency-call function, with the function only partially available; service contact is requested.Emergency call function: malfunction! Function unavailable. Please contact serviceThis Audi alert indicates that the emergency call function is unavailable and asks the driver to contact service. Verified manufacturer communications document the same instrument-cluster warning and refer to diagnostic trouble codes stored in the Emergency Call Module and Communication Unit.Vehicle lights: fault. Please contact workshopVerified diagnostic recordSOS Emergency Call function: malfunction. Function unavailable. Please contact serviceFor certain 2023 US Audi Q5, e-tron, e-tron GT, and RS e-tron GT vehicles, this alert indicates that the SOS Emergency Call function is malfunctioning or unavailable. Audi’s referenced technical service bulletin documents the instrument-cluster message and directs the customer to contact service.Emergency call function: fault. Function partially available. Please contact workshopFor 2022–2024 US Audi Q4 e-tron vehicles, Audi/NHTSA manufacturer communication 11005934 documents the instrument-cluster message: “Emergency call function: fault. Function partially available. Please contact workshop.” Contact an Audi workshop for diagnosis.Rear cross-traffic assist: currently unavailable. See ownerThis Audi alert means rear cross-traffic assist is currently unavailable. Verified Audi service-bulletin evidence states the condition can occur sporadically and may not be reproducible during a workshop visit.Parking aid: fault. Obstacles cannot be detectedThis Audi alert means the parking aid is not working and obstacles cannot be detected by that function. Verified evidence supports the message and loss of parking-aid operation; the underlying cause is not yet established by verified evidence.Maneuver assist: fault. Please contact workshop.This Audi alert means: “Maneuver assist: fault. Please contact workshop.” Verified manufacturer communications identify it as a maneuver-assist malfunction message. Contact an Audi workshop for diagnosis.Vehicle start system: fault. Please contact workshopVerified diagnostic recordStart/stop system: system fault. Function unavailable. Please contact workshopThis Audi instrument-cluster alert indicates that the start/stop system is unavailable because the vehicle has detected a system fault. The supplied official Audi manufacturer communication instructs contact with a workshop.Child lock: faultVerified diagnostic recordPower unit start system: fault. Please contact workshopFor a 2024 US Audi Q8 e-tron, this alert is covered by Audi Circular/Dealer 57DN evidence describing an intermittent software error that can display the message and store a diagnostic trouble code even when no actual vehicle malfunction exists. Contact an Audi workshop for evaluation.Engine start system: Fault orVerified diagnostic recordFault: Limited warning messgesVerified diagnostic recordShock absorbers: fault. Journey can be continuedAudi identifies this as an instrument-cluster message: “Shock absorbers: fault. Journey can be continued.” Official Audi TSB information exists for this message on certain 2025 Q6 e-tron and SQ6 e-tron vehicles in the US.P0617Verified diagnostic recordP0615Verified diagnostic recordP0000Verified diagnostic record