Genesis P075300
For Genesis G80 model years 2023–2024 in the US, P075300 is referenced in NHTSA manufacturer communication 19-AT-008G as one of the solenoid codes for which an Automatic Transaxle “Oil Pressure Characteristics Input (Solenoid valve Replacement)” procedure is necessary.
Evidence snapshot
Last evidence review: 2026-10-12. Applicability is shown only where a model relationship is supported by evidence.
Quick answer
For Genesis G80 model years 2023–2024 in the US, P075300 is referenced in NHTSA manufacturer communication 19-AT-008G as one of the solenoid codes for which an Automatic Transaxle “Oil Pressure Characteristics Input (Solenoid valve Replacement)” procedure is necessary.
This page separates verified manufacturer/regulator evidence from supporting material. Unsupported causes, repairs or safety conclusions are not guessed.
Watch Videos
Relevant videos play here without leaving this diagnostic page.
No sufficiently relevant embeddable video has been accepted for this diagnostic yet.
Videos are supporting material and never override OEM or regulator evidence.
1. What does Genesis P075300 mean?
For Genesis G80 model years 2023–2024 in the US, P075300 is referenced in NHTSA manufacturer communication 19-AT-008G as one of the solenoid codes for which an Automatic Transaxle “Oil Pressure Characteristics Input (Solenoid valve Replacement)” procedure is necessary.
2. Technical explanation
The verified source does not provide a diagnostic definition for P075300. It identifies P075300 in a list of solenoid-related DTCs and states that the Oil Pressure Characteristics Input procedure is necessary for specified solenoids, including P075300. The documented process uses GDS service software and requires entering an 8-digit code recorded during an earlier step. The source excerpt does not establish the specific failed component, failure mechanism, or conditions that set the code.
3. What system is affected?
Automatic transaxle / solenoid valve service procedure, based on NHTSA manufacturer communication 19-AT-008G.
4. How serious is this code?
Not yet established by verified evidence.
5. Genesis P075300 symptoms you may notice
Not yet established by verified evidence.
6. Possible causes of Genesis P075300
- Not yet established by verified evidence.
7. Can I drive with Genesis P075300?
Not yet established by verified evidence.
8. Can I charge with Genesis P075300?
Not yet established by verified evidence.
9. What you can safely do
- Arrange professional diagnosis using the applicable Genesis service information and GDS process.
- Do not attempt solenoid replacement or transmission control programming based solely on this code without qualified service assessment.
10. How to troubleshoot Genesis P075300
- Verified evidence identifies a GDS Automatic Transaxle Oil Pressure Characteristics Input procedure for specified solenoid replacement, including P075300.
- The procedure requires entering an 8-digit code recorded in an earlier service step twice in GDS.
- The supplied evidence does not establish the complete diagnostic sequence, test criteria, or repair decision process for this code.
11. When to contact service
Contact a Genesis dealer or qualified transmission service provider for diagnosis. The verified source describes a manufacturer service-software procedure associated with P075300.
12. What the service center may check
- Confirm whether P075300 is present using appropriate diagnostic equipment.
- If a relevant solenoid valve has been replaced, perform the applicable GDS Automatic Transaxle Oil Pressure Characteristics Input procedure as directed by the manufacturer service information.
- Enter the documented 8-digit code in GDS when prompted by the procedure.
13. Possible repair or resolution for Genesis P075300
- The verified evidence supports completing the Oil Pressure Characteristics Input procedure after applicable solenoid valve replacement for P075300.
- Whether a solenoid requires replacement is not established by the supplied verified evidence.
14. Affected vehicles
- Genesis G80 · 2023–2024 · US
15. Related TSBs / service bulletins
- NHTSA Manufacturer Communication PDF 10253024, TSB 19-AT-008G, published April 8, 2019. It lists P075300 among solenoid DTCs and documents an Automatic Transaxle Oil Pressure Characteristics Input procedure for specified solenoid replacement. Source: https://static.nhtsa.gov/odi/tsbs/2019/MC-10253024-0001.pdf
16. Recall information
No recall relationship is established by verified evidence.
17. Official manufacturer information
Verified source coverage for this diagnostic is listed below. Open the cited document for the full manufacturer or regulator context.
19. Genesis P075300 frequently asked questions
What does P075300 mean?
A specific diagnostic definition is not yet established by the supplied verified evidence. The source lists P075300 as a solenoid DTC in an automatic-transaxle service bulletin.
Does P075300 require a programming procedure?
The verified bulletin states that the GDS Oil Pressure Characteristics Input procedure is necessary for specified solenoids, including P075300, in the context of solenoid valve replacement.
Can I drive with P075300?
Not yet established by verified evidence.
Is P075300 covered by a recall?
No recall information is established by the supplied verified evidence.
20. Sources & verification
Evidence sources: 1 · Page reviewed 2026-10-12 · Editorial & quality policy