Genesis P076800
19-AT-008G Page 12 of 12 31. Input the 8-digit code recorded in Step 10 in the blank spaces in the GDS. Select OK. Input the 8 digit code again and select OK. The GDS will confirm
Quick answer
For applicable 2023–2024 Genesis G80 vehicles in the US, P076800 is referenced in Genesis bulletin 19-AT-008G as a solenoid-related automatic-transaxle DTC. The bulletin specifies an Oil Pressure Characteristics Input procedure after replacement of certain solenoids, including P076800.
This page separates verified manufacturer/regulator evidence from supporting material. Unsupported causes, repairs or safety conclusions are not guessed.
Watch Videos
Relevant videos play here without leaving this diagnostic page.
No sufficiently relevant embeddable video has been accepted for this diagnostic yet.
Videos are supporting material and never override OEM or regulator evidence.
1. What does P076800 mean?
For applicable 2023–2024 Genesis G80 vehicles in the US, P076800 is referenced in Genesis bulletin 19-AT-008G as a solenoid-related automatic-transaxle DTC. The bulletin specifies an Oil Pressure Characteristics Input procedure after replacement of certain solenoids, including P076800.
2. Technical explanation
Verified evidence identifies P076800 in NHTSA-posted Genesis TSB 19-AT-008G. The bulletin directs use of GDS S/W Management > Automatic Transaxle > Oil Pressure Characteristics Input (Solenoid Valve Replacement), selection of the applicable solenoid type, and entry of an 8-digit code recorded earlier in the bulletin procedure. The supplied evidence does not establish the plain-language fault definition of P076800.
3. What system is affected?
Automatic transaxle / solenoid oil-pressure characteristics procedure.
4. How serious is this code?
Unknown. Verified evidence does not assign a severity level.
5. Symptoms you may notice
- Not yet established by verified evidence.
6. Possible causes
- Not yet established by verified evidence.
7. Can I still drive the vehicle?
Unknown. Verified evidence does not establish whether the vehicle is safe to drive with P076800.
8. Can I charge the vehicle?
Unknown. Verified evidence does not establish charging status or charging safety for this DTC.
9. What you can safely do
- Arrange diagnosis by a Genesis-qualified service facility.
- Do not attempt automatic-transaxle solenoid replacement or GDS programming without qualified service support.
10. Step-by-step troubleshooting
- A service technician can consult Genesis TSB 19-AT-008G.
- For the solenoids identified in the bulletin, including P076800, the bulletin calls for GDS Oil Pressure Characteristics Input following solenoid replacement.
- The procedure includes entering an 8-digit code recorded during an earlier step and confirming it in GDS.
11. When to contact service
Contact an authorized Genesis service center for diagnosis and to determine whether TSB 19-AT-008G applies to the vehicle and repair condition.
12. What the service center may check
- Confirm vehicle applicability: Genesis G80, model years 2023–2024, US market.
- Retrieve and assess DTC P076800 using Genesis diagnostic equipment.
- If a relevant solenoid has been replaced, perform the bulletin-specified GDS Oil Pressure Characteristics Input procedure as applicable.
- Enter and confirm the required 8-digit code in GDS as directed by the bulletin.
13. Possible repair or resolution
- Verified evidence supports a post-solenoid-replacement GDS oil-pressure-characteristics input procedure for P076800.
- Whether a solenoid requires replacement, and the final repair outcome, are not yet established by verified evidence.
14. Affected vehicles
- Genesis G80 · 2023–2024 · US
15. Related TSBs / service bulletins
- Genesis TSB 19-AT-008G, published through NHTSA as Manufacturer Communication PDF 10253024 on 2019-04-08. It includes P076800 among solenoid DTCs requiring the specified Oil Pressure Characteristics Input procedure after applicable solenoid replacement.
16. Recall information
- Not yet established by verified evidence.
17. Official manufacturer information
Official source: NHTSA Manufacturer Communication PDF 10253024, Genesis TSB 19-AT-008G: https://static.nhtsa.gov/odi/tsbs/2019/MC-10253024-0001.pdf
19. Frequently asked questions
What does P076800 mean on a Genesis G80?
The supplied verified evidence does not establish a plain-language definition. It identifies P076800 as a solenoid-related automatic-transaxle DTC in Genesis TSB 19-AT-008G.
Does P076800 require programming after a solenoid replacement?
The bulletin states that the GDS Oil Pressure Characteristics Input procedure is necessary for listed solenoids, including P076800, following the applicable solenoid replacement procedure.
Is it safe to drive with P076800?
Not yet established by verified evidence.